Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung Nächste Überarbeitung Beide Seiten der Revision | ||
pr430 [2018/04/13 11:52] dh3wr |
pr430 [2018/04/13 12:11] dh3wr [PR430] |
||
---|---|---|---|
Zeile 23: | Zeile 23: | ||
Power on the PR430 and connect it with the above mentioned serial interface cable to the serial interface of this PC. | Power on the PR430 and connect it with the above mentioned serial interface cable to the serial interface of this PC. | ||
+ | == Setting RS232 parameters == | ||
Start the software ''SERIAL.EXE''. | Start the software ''SERIAL.EXE''. | ||
Zeile 41: | Zeile 42: | ||
Keep f=8n and h=n! | Keep f=8n and h=n! | ||
- | * Programm: serial.exe | + | <code>serial.exe b=<Baud rate> f=<Data format> h=<Handshake> w=<Delay></code> |
- | * Parameter: | + | * Parameters: |
- | * * b=Baud rate; Allowed values: 1200 to 38400 Baud | + | * <Baud rate>: Allowed values: 1200 to 38400 Baud |
- | * * f= Data format; 7/8 Bit, (n)o / (e)ven / (o)dd Parity | + | * <Data format>: 7/8 Bit, (n)o / (e)ven / (o)dd Parity |
- | * * h= Handshake; (h)ardware RTS/CTS, (s)oftware XON/XOFF, (n)one | + | * <Handshake>: (h)ardware RTS/CTS, (s)oftware XON/XOFF, (n)one |
- | * * w= Delay between characters in ms. | + | * <Delay>: Delay between characters in ms. |
- | * Beispiel: | + | * Example: |
- | * * serial b=19200 f=8n h = n (sets 19200 Baud, 8 Bit, No Parity, No Handshake) | + | * serial b=19200 f=8n h = n (sets 19200 Baud, 8 Bit, No Parity, No Handshake) |
+ | == Configure PR430 to POCSAG mode == | ||
Now you will use the second software ''MGSC.EXE'' to configure the updated PR430 software. | Now you will use the second software ''MGSC.EXE'' to configure the updated PR430 software. | ||
Start ''mgsc'' without parameters and after a fresh updated PR430 you should see the text message | Start ''mgsc'' without parameters and after a fresh updated PR430 you should see the text message | ||
Zeile 74: | Zeile 75: | ||
Use <code>mgsc F0</code> to change the internal TNC to KISS mode. | Use <code>mgsc F0</code> to change the internal TNC to KISS mode. | ||
The software answer with ''POCSAG Mode, Mycall DB0ABC-7, Master DB0ABC-12 KISS''. The frequency information is not shown in this output, but it's still active. | The software answer with ''POCSAG Mode, Mycall DB0ABC-7, Master DB0ABC-12 KISS''. The frequency information is not shown in this output, but it's still active. | ||
+ | |||
+ | <code>mgsc.exe [M=<Mode> I:<CallsignTX> P:<CallsignMaster> F:<Frequency>[-|--|---][A]|FO]</code> | ||
+ | * Parameters: | ||
+ | * <Mode>: 3: POCSAG Mode, 5: PC/FlexNet Mode | ||
+ | * <CallsignTX>: AX.25-Callsign for this TX, [-SSID] | ||
+ | * <CallsignMaster>: AX.25-Callsign for the Master, [-SSID] | ||
+ | * <Frequency>: Frequency in kHz, decimal limiter is '','' | ||
+ | The ''-'' are setting a Duplex shift, which is only used for packet radio operation and are not necessary for POCSAG operation. So this information is for completness only. | ||
+ | |||
+ | - : 1.6 MHz TX frequency shift | ||
+ | |||
+ | - - : 7.6 MHz TX frequency shift | ||
+ | |||
+ | - - - : 9.4 MHz TX frequency shift | ||
+ | |||
+ | A: Use AFSK 1200 baud mode, if not given use FSK 9600 Baud mode | ||
+ | |||
+ | * FO: Set to KISS MODE | ||
+ | * Example: | ||
+ | * mgsc M=3 I:db0xyz-7 P:db0xyz-12 F:438350- - | ||
+ | |||
+ | |||
+ | The parameters can also be given one by one running the program serveral times. | ||
Now your PR430 is configured correctly and you can connect it to your Raspberry PI serial interface. | Now your PR430 is configured correctly and you can connect it to your Raspberry PI serial interface. |