Benutzer-Werkzeuge
pr430
Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
| Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung Nächste Überarbeitung Beide Seiten der Revision | ||
|
pr430 [2018/04/13 12:08] dh3wr |
pr430 [2018/04/18 10:27] dh3wr |
||
|---|---|---|---|
| Zeile 42: | Zeile 42: | ||
| Keep f=8n and h=n! | Keep f=8n and h=n! | ||
| - | ''serial.exe b=<Baud rate> f=<Data format> h=<Handshake> w=<Delay>'' | + | <code>serial.exe b=<Baud rate> f=<Data format> h=<Handshake> w=<Delay></code> |
| * Parameters: | * Parameters: | ||
| * <Baud rate>: Allowed values: 1200 to 38400 Baud | * <Baud rate>: Allowed values: 1200 to 38400 Baud | ||
| Zeile 61: | Zeile 61: | ||
| change the mode of the PR430 to POCSAG mode. The software will answer a text with ''POCSAG Mode, Mycall NO CALL, Master undefined, Mode undefined'' | change the mode of the PR430 to POCSAG mode. The software will answer a text with ''POCSAG Mode, Mycall NO CALL, Master undefined, Mode undefined'' | ||
| - | Now you define the callsing of the POCSAG transmitter and the master call, and the POCSAG frequency with the following commands. We are using the same call signs as in the description of th e configuration below, so please change ''DB0ABC-7'' and ''DB0ABC-12'' to your POCSAG transmitters licensed callsign! | + | Now you define the callsing of the POCSAG transmitter and the master call, and the POCSAG frequency with the following commands. We are using the same call signs as in the description of the configuration below, so please change ''DB0ABC-7'' and ''DB0ABC-12'' to your POCSAG transmitters licensed callsign! |
| **Remark**: These settings are just used on the AX.25 connection. They have nothing to do with the DAPNET configuration on the DAPNET-Network. But they are necessary in the ''DAPNET-Proxy'' setup described below. | **Remark**: These settings are just used on the AX.25 connection. They have nothing to do with the DAPNET configuration on the DAPNET-Network. But they are necessary in the ''DAPNET-Proxy'' setup described below. | ||
| Zeile 76: | Zeile 76: | ||
| The software answer with ''POCSAG Mode, Mycall DB0ABC-7, Master DB0ABC-12 KISS''. The frequency information is not shown in this output, but it's still active. | The software answer with ''POCSAG Mode, Mycall DB0ABC-7, Master DB0ABC-12 KISS''. The frequency information is not shown in this output, but it's still active. | ||
| - | ''mgsc.exe [M=<Mode> I:<CallsignTX> P:<CallsignMaster> F:<Frequency>[-|--|---][A]|FO]'' | + | <code>mgsc.exe [M=<Mode> I:<CallsignTX> P:<CallsignMaster> F:<Frequency>[-|--|---]|FO]</code> |
| * Parameters: | * Parameters: | ||
| * <Mode>: 3: POCSAG Mode, 5: PC/FlexNet Mode | * <Mode>: 3: POCSAG Mode, 5: PC/FlexNet Mode | ||
| * <CallsignTX>: AX.25-Callsign for this TX, [-SSID] | * <CallsignTX>: AX.25-Callsign for this TX, [-SSID] | ||
| * <CallsignMaster>: AX.25-Callsign for the Master, [-SSID] | * <CallsignMaster>: AX.25-Callsign for the Master, [-SSID] | ||
| - | * <Frequency>: Frequency in kHz: [-|--|---][A] | + | * <Frequency>: Frequency in kHz, decimal limiter is '','' |
| The ''-'' are setting a Duplex shift, which is only used for packet radio operation and are not necessary for POCSAG operation. So this information is for completness only. | The ''-'' are setting a Duplex shift, which is only used for packet radio operation and are not necessary for POCSAG operation. So this information is for completness only. | ||
| - : 1.6 MHz TX frequency shift | - : 1.6 MHz TX frequency shift | ||
| + | |||
| -- : 7.6 MHz TX frequency shift | -- : 7.6 MHz TX frequency shift | ||
| - | --- : 9.4 MHz TX frequency shift | ||
| - | A: Use AFSK 1200 baud mode, if not given use FSK 9600 Baud mode | ||
| - | |||
| - | * FO: Set to KISS MODE | ||
| - | * Example: | ||
| - | * mgsc M=3 I:db0xyz-7 P:db0xyz-12 F:438350-- | ||
| + | - - - : 9.4 MHz TX frequency shift | ||
| The parameters can also be given one by one running the program serveral times. | The parameters can also be given one by one running the program serveral times. | ||
pr430.txt · Zuletzt geändert: 2018/04/18 20:52 von dh3wr
Seiten-Werkzeuge
Falls nicht anders bezeichnet, ist der Inhalt dieses Wikis unter der folgenden Lizenz veröffentlicht: CC Attribution-Share Alike 4.0 International
