pr430
Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
| Beide Seiten der vorigen RevisionVorhergehende ÜberarbeitungNächste Überarbeitung | Vorhergehende Überarbeitung | ||
| pr430 [2018/04/13 09:47] – dh3wr | pr430 [2018/04/18 18:52] (aktuell) – [Automated start of the DAPNET-Proxy] dh3wr | ||
|---|---|---|---|
| Zeile 23: | Zeile 23: | ||
| Power on the PR430 and connect it with the above mentioned serial interface cable to the serial interface of this PC. | Power on the PR430 and connect it with the above mentioned serial interface cable to the serial interface of this PC. | ||
| + | == Setting RS232 parameters == | ||
| Start the software '' | Start the software '' | ||
| Zeile 41: | Zeile 42: | ||
| Keep f=8n and h=n! | Keep f=8n and h=n! | ||
| - | The detailed command set is described here: | + | < |
| - | FIXME | + | * Parameters: |
| + | * <Baud rate>: Allowed values: 1200 to 38400 Baud | ||
| + | * <Data format>: 7/8 Bit, (n)o / (e)ven / (o)dd Parity | ||
| + | * < | ||
| + | * < | ||
| + | * Example: | ||
| + | * serial b=19200 f=8n h = n (sets 19200 Baud, 8 Bit, No Parity, No Handshake) | ||
| + | == Configure PR430 to POCSAG mode == | ||
| Now you will use the second software '' | Now you will use the second software '' | ||
| Start '' | Start '' | ||
| Zeile 53: | Zeile 61: | ||
| change the mode of the PR430 to POCSAG mode. The software will answer a text with '' | change the mode of the PR430 to POCSAG mode. The software will answer a text with '' | ||
| - | Now you define the callsing of the POCSAG transmitter and the master call, and the POCSAG frequency with the following commands. We are using the same call signs as in the description of th e configuration below, so please change '' | + | Now you define the callsing of the POCSAG transmitter and the master call, and the POCSAG frequency with the following commands. We are using the same call signs as in the description of the configuration below, so please change '' |
| **Remark**: These settings are just used on the AX.25 connection. They have nothing to do with the DAPNET configuration on the DAPNET-Network. But they are necessary in the '' | **Remark**: These settings are just used on the AX.25 connection. They have nothing to do with the DAPNET configuration on the DAPNET-Network. But they are necessary in the '' | ||
| Zeile 59: | Zeile 67: | ||
| < | < | ||
| mgsc I:DB0ABC-7 | mgsc I:DB0ABC-7 | ||
| - | mgsc P: DB0ABC-12 | + | mgsc P:DB0ABC-12 |
| mgsc F:439987,5 | mgsc F:439987,5 | ||
| </ | </ | ||
| Zeile 67: | Zeile 75: | ||
| Use < | Use < | ||
| The software answer with '' | The software answer with '' | ||
| + | |||
| + | < | ||
| + | * Parameters: | ||
| + | * < | ||
| + | * < | ||
| + | * < | ||
| + | * < | ||
| + | The '' | ||
| + | |||
| + | - : 1.6 MHz TX frequency shift | ||
| + | |||
| + | -- : 7.6 MHz TX frequency shift | ||
| + | |||
| + | - - - : 9.4 MHz TX frequency shift | ||
| + | |||
| + | The parameters can also be given one by one running the program serveral times. | ||
| Now your PR430 is configured correctly and you can connect it to your Raspberry PI serial interface. | Now your PR430 is configured correctly and you can connect it to your Raspberry PI serial interface. | ||
| Zeile 138: | Zeile 162: | ||
| < | < | ||
| - | If you type now < | + | If you type now < |
| Try to connect via KISS and AX.25 to your PR430 or RPC. | Try to connect via KISS and AX.25 to your PR430 or RPC. | ||
| - | < | + | < |
| You should see the command line interface of the POCSAG software running on your PR430 or RPC. If not done already, now it's the time to do (and store**(!)**) some settings on the PR430. | You should see the command line interface of the POCSAG software running on your PR430 or RPC. If not done already, now it's the time to do (and store**(!)**) some settings on the PR430. | ||
| * Set the master callsign to db0abc-12 | * Set the master callsign to db0abc-12 | ||
| Zeile 177: | Zeile 201: | ||
| </ | </ | ||
| Restart the xinetd daemon with | Restart the xinetd daemon with | ||
| - | < | + | < |
| Try if the connection and conversion is working: | Try if the connection and conversion is working: | ||
| Zeile 206: | Zeile 230: | ||
| cd /opt | cd /opt | ||
| sudo git clone https:// | sudo git clone https:// | ||
| - | chown -R pi / | + | sudo chown -R pi / |
| cd / | cd / | ||
| </ | </ | ||
| Zeile 217: | Zeile 241: | ||
| Copy the example config file to that directory. Change the callsign according to your needs. | Copy the example config file to that directory. Change the callsign according to your needs. | ||
| < | < | ||
| - | cp / | + | cp / |
| - | / | + | |
| </ | </ | ||
| Zeile 265: | Zeile 288: | ||
| In a second SSH session or terminal, you can watch the AX.25 traffic on '' | In a second SSH session or terminal, you can watch the AX.25 traffic on '' | ||
| - | < | + | < |
| If you are familiar with AX.25, this will give a good hints for debugging. | If you are familiar with AX.25, this will give a good hints for debugging. | ||
| Zeile 288: | Zeile 311: | ||
| ExecStopPost=-/ | ExecStopPost=-/ | ||
| WorkingDirectory=/ | WorkingDirectory=/ | ||
| - | ExecStart=/ | + | ExecStart=/ |
| StandardOutput=null | StandardOutput=null | ||
| StandardError=null | StandardError=null | ||
pr430.1523612835.txt.gz · Zuletzt geändert: 2018/04/13 09:47 von dh3wr