Benutzer-Werkzeuge

Webseiten-Werkzeuge


primodescription

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen Revision Vorhergehende Überarbeitung
Nächste Überarbeitung
Vorhergehende Überarbeitung
primodescription [2019/03/18 18:22]
do1cgi [Re-aligning the RF components]
primodescription [2022/01/11 18:09] (aktuell)
do1goe [Anleitung]
Zeile 3: Zeile 3:
 {{::​primo:​primo.jpg?​direct&​400 |}} {{::​primo:​primo.jpg?​direct&​400 |}}
  
-These pagers were available in the former POCSAG net by Deutsche Telekom AG and later by e*message. The HF part of the receiver is identical to [[skyperdescription|Skypers]]. The modification for 439.9875 MHz is thus the same. The shortcome is that the display is much smaller and there is no built-in function for setting time and date autmatically. In addition the date only allows years up to (20)13 starting from (19)94 to be set. This has to be done by hand and is lost on longer absence of battery power.+These pagers were available in the former POCSAG net by Deutsche Telekom AG and later by e*cityruf. The HF part of the receiver is identical to [[skyperdescription|Skypers]]. The modification for 439.9875 MHz is thus the same. The shortcome is that the display is much smaller and there is no built-in function for setting time and date automatically. In addition the date only allows years up to (20)13 starting from (19)94 to be set. This has to be done by hand and is lost on longer absence of battery power. 
 + 
 +Der Pager ist von der Firma NEC hergestellt. Modell: NEC PA4PY-20A
  
 ===== Modification for UHF ham band use ===== ===== Modification for UHF ham band use =====
Zeile 54: Zeile 56:
 ===== RIC programming ===== ===== RIC programming =====
  
-The Primo pagers obviously share some similarities with Skypers. ​There is a connector ​for external programming which probably ​is the same as found on Skypers. ​This needs further investigation.+The Primo pagers obviously share some similarities with Skypers. ​ 
 + 
 +==== Reading programmed RICs ==== 
 + 
 +If you just want to know which RIC(s) are programmed in your Primo pager there is a special key combination that was deteced by DK7DB. Turn the pager off and press "​M"​ twice. It will show the programmed RICs 1 to 3. 
 + 
 + 
 +{{ :​primo:​primo_reading_ric_manually.jpg?​600 |}} 
 + 
 +==== Hardware ==== 
 + 
 +The connector ​on the display PCB is identical to the [[skyperdescription#​hardware|interface ​found on Skypers]]. The connector looks as follows:  
 + 
 +{{ :​primo:​primo_progger_interface.jpg?​direct&​600 | Primo programming interface }} 
 + 
 +==== Software ==== 
 + 
 +Using the same programmer as for Skypers ([[skyperdescription#​hardware|linked here]]) you read at least read the RIC from the pager. After starting the software you have to load the correct .ROM file. In this case we used 20bd-a.rom and after pressing F1 to read the pager the correct RIC was displayed.  
 + 
 +{{ :​primo:​primo_reading_ric.jpg?​direct&​600 | Successfully read the RIC off a Primo pager }} 
 + 
 +Wrting the pager has not been tested as we are not sure if the .rom file is 100% correct yet. 
 + 
 +==== Anleitung ==== 
 + 
 +Zum bedienen des Pagers ist eine Bedienungsanleitung bei "​E*Cityruf"​ zu finden. 
 +https://​www.emessage.de/​ecityruf/​service/​bedienungsanleitung.php 
 + 
 +Hier die Bedienungsanleitung,​ die dem Primo mal bei lag: 
 +{{ :​primo:​primo_anleitung.pdf |}} 
  
  
primodescription.1552929723.txt.gz · Zuletzt geändert: 2019/03/18 18:22 von do1cgi