Benutzer-Werkzeuge

Webseiten-Werkzeuge


mmdvm

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung
Vorhergehende Überarbeitung
mmdvm [2025/05/18 19:50] – on6rfmmdvm [2025/09/13 16:23] (aktuell) – [Upgrade the firmware of your MMDVM-Hardware] pe2kmv
Zeile 4: Zeile 4:
  
 ===== Hardware ===== ===== Hardware =====
-  * MMDVM +  * MMDVM (modem with external analog radios) OR 
-  * MMDVM_HS_Hat+  * MMDVM_HS_Hat OR
   * MMDVM_DUAL_HAT   * MMDVM_DUAL_HAT
  
Zeile 19: Zeile 19:
   * [[skyperdescription|Skyper]]   * [[skyperdescription|Skyper]]
   * [[alphapocdescription|AlphaPoc 602R X4]] (z.Z. ausverkauft) - TPL Birdy   * [[alphapocdescription|AlphaPoc 602R X4]] (z.Z. ausverkauft) - TPL Birdy
-  * [[swissphone|Swissphone pagers]]+  * [[swissphonedescription|Swissphone pagers]]
  
  
-====== How to set up Pi* for POCSAG (DAPNET) with MMDVM_HS_HAT or MMDVM_DUAL_HAT ======+====== How to set up Pi* or WPSD for POCSAG (DAPNET) with MMDVM_HS_HAT or MMDVM_DUAL_HAT ======
  
 Already have a working installation of Pi-Star (Pi*)? Already have a working installation of Pi-Star (Pi*)?
Zeile 68: Zeile 68:
  
 for Upgrading MMDVM_HS_Hat board conected to GPIO you have to enter the command: for Upgrading MMDVM_HS_Hat board conected to GPIO you have to enter the command:
-<code>sudo pistar-mmdvmhshatflash hs_hat</code>+<code>sudo pistar-modemupgrade hs_hat</code>
  
 for upgrading the original MMDVM-HS_DUAL_HAT board (made by Andy, Florian (DF2ET) and DB9HAT) conected to GPIO  you have to enter the command: for upgrading the original MMDVM-HS_DUAL_HAT board (made by Andy, Florian (DF2ET) and DB9HAT) conected to GPIO  you have to enter the command:
  
-<code>sudo pistar-mmdvmhshatflash hs_dual_hat</code>+<code>sudo pistar-modemupgrade hs_dual_hat</code>
  
 If you get a message that the flashing process was successfull, the hardest part is done. If not, repeat flashing or ask for help in the "MMDVM-BM" or "DAPNET User" Telegram-Messenger Groups. If you get a message that the flashing process was successfull, the hardest part is done. If not, repeat flashing or ask for help in the "MMDVM-BM" or "DAPNET User" Telegram-Messenger Groups.
Zeile 78: Zeile 78:
 Newer board variants are equipped with a 12.288MHz TCXO and require a firmware with different settings. The commands above flash a 14.7456MHz firmware. To upgrade boards with a 12.288MHz use the following commands: Newer board variants are equipped with a 12.288MHz TCXO and require a firmware with different settings. The commands above flash a 14.7456MHz firmware. To upgrade boards with a 12.288MHz use the following commands:
  
-<code>sudo pistar-mmdvmhshatflash hs_hat-12mhz</code>+<code>sudo pistar-modemupgrade hs_hat-12mhz</code>
  
 respectively respectively
  
-<code>sudo pistar-mmdvmhshatflash hs_dual_hat-12mhz</code>+<code>sudo pistar-modemupgrade hs_dual_hat-12mhz</code>
  
 Be sure to identify your TCXO before flashing the firmware! Be sure to identify your TCXO before flashing the firmware!
Zeile 91: Zeile 91:
 <code>sudo reboot now [Enter]</code> <code>sudo reboot now [Enter]</code>
      
-====== Configure Pi-Star and enable DAPNET ======+====== Configure Pi-Star or WPSD and enable DAPNET ======
  
  If not already done you should register on [[https://www.hampager.de]] and than [[procedurenewtx|Register a New Transmitter]].  If not already done you should register on [[https://www.hampager.de]] and than [[procedurenewtx|Register a New Transmitter]].
mmdvm.1747597843.txt.gz · Zuletzt geändert: 2025/05/18 19:50 von on6rf