Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- raspagerc9000 [2018/09/10 18:40] – df2et
+++ raspagerc9000 [2026/01/30 13:13] (aktuell) – Fix urls dj7lc
@@ Zeile 149: / Zeile 149: @@
+==== Front Panel LEDs =====
+You can wire two LEDs to the RasPagerC9000 board that can be integrated into the front panel. The wires need to be connected to pins 5,6,7 of RasPagerC9000. The pinout is as follows:
+  * Pin 5: GND
+  * Pin 6: SWAct
+  * Pin 7: MasterConn
+{{ :c9000:c9000leds.png?nolink&600 | Pinout for Fron Panel LEDs}}
+These LEDs indicate if UniPager is connected to the Master (MasterConn) and when its active (SWAct). The corresponding LEDs are not controlled by UniPager directly. You have to use the extra python script called unipagerled.py. It is sufficient to use the preset from the example in the config (/etc/unipagerledconfig.py):
+   preset = "c9000"
+Two resistors (330R) are already present on the PCB (see R10 and R11). The two LEDs can be mounted on the fron panel of the Base Station Controller.
+{{ :c9000:c9000frontpanelleds.jpg?nolink&600 | Front Panel LEDs}}
 ==== Temperature Monitoring ====
 The RasPagerC9000 PCB is already prepared for easy implementation of a temperature monitoring of the C9000. It is done by cheap DS18x20 OneWire temperature sensors. In order to activate the built-in support for OneWire temperature sensors in the Raspbian software, add the following line tho ''/boot/config.txt''
@@ Zeile 194: / Zeile 211: @@
 </code>
-Change the part where the localhost entry is given a a useful name of your C9000. The example here is ''c9000.db0sda.ampr.org''.
+Change the part where the localhost entry is given a a useful name of your C9000. The example here is ''c9000.db0sda.hamnet.radio''.
 <file>
 # a simple host tree
-[c9000.db0sda.ampr.org]
+[c9000.db0sda.hamnet.radio]
     address localhost
     use_node_name yes
@@ Zeile 301: / Zeile 318: @@
 #contact.nagios.command /usr/bin/send_nsca nagios.host.comm -c /etc/nsca.conf
-[c9000.db0sda.ampr.org]
+[c9000.db0sda.hamnet.radio]
     address localhost
     use_node_name yes
@@ Zeile 314: / Zeile 331: @@
 # telnetting to localhost, port 4949
 #
-host_name c9000.db0sda.ampr.org
+host_name c9000.db0sda.hamnet.radio
 </file>
@@ Zeile 355: / Zeile 372: @@
 # telnetting to localhost, port 4949
 #
-host_name c9000.db0sda.ampr.org
+host_name c9000.db0sda.hamnet.radio
 # A list of addresses that are allowed to connect.  This must be a
@@ Zeile 561: / Zeile 578: @@
 define service{
         use                             generic-service-rwthafu
-        host_name                       c9000.db0sda.ampr.org
+        host_name                       c9000.db0sda.hamnet.radio
         service_description             PA Temperature
         check_command                   check_nrpe_1arg!check_PA_temp
@@ Zeile 569: / Zeile 586: @@
 define service{
         use                             generic-service-rwthafu
-        host_name                       c9000.db0sda.ampr.org
+        host_name                       c9000.db0sda.hamnet.radio
         service_description             C9000 Temperature
         check_command                   check_nrpe_1arg!check_C9000_temp
@@ Zeile 603: / Zeile 620: @@
 https://github.com/phl0/C9000PADummyDisplay
-The author has some PCBs to sell at cose. Please contact DF2ET if you are interested.
+The author has some PCBs to sell at cost. Please contact DF2ET if you are interested.
 The 7-segement display is supported by the C9000PADummy Arduino code. To activate it you have to compile the code with