ax25
Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
| Nächste Überarbeitung | Vorhergehende Überarbeitung | ||
| ax25 [2018/01/08 10:24] – angelegt dh3wr | ax25 [2018/02/27 10:08] (aktuell) – [Connecting old Packet-Radio only transmitters via AX.25] dh3wr | ||
|---|---|---|---|
| Zeile 1: | Zeile 1: | ||
| ====== Connecting old Packet-Radio only transmitters via AX.25 ====== | ====== Connecting old Packet-Radio only transmitters via AX.25 ====== | ||
| - | There are several reasons why one would like to connect an old AX.25 Packet-Radio only Transmitter to the DAPNET: | + | There are several reasons why one would like to connect an old AX.25 Packet-Radio only Transmitter to the DAPNET: |
| - | * No IP connectivity at the transmitter location | + | * No possibility to change the hardware due to restrictions or motivation |
| - | * Sentimental reasons to keep the RPC PCB :-) | + | * No IP connectivity at the transmitter location |
| + | * Sentimental reasons to keep the RPC PCB :-) | ||
| For thoses cases we provide two possible solutions: | For thoses cases we provide two possible solutions: | ||
| Zeile 19: | Zeile 20: | ||
| - The antenna gain minus the cable losses in dBi | - The antenna gain minus the cable losses in dBi | ||
| - The output power in Watt | - The output power in Watt | ||
| - | - the antenna height above ground (not NN!) | + | - the antenna height above ground |
| The DAPNET team will check you request and provide a software solution with dapnet-proxy to connect your transmitter to the network. | The DAPNET team will check you request and provide a software solution with dapnet-proxy to connect your transmitter to the network. | ||
| - | TBC | + | ===== Individual interfacing from AX.25 to TCP ===== |
| + | If you don't like the centralized way of connecting your old AX.25 transmitter, | ||
| + | |||
| + | The following steps are needed: | ||
| + | |||
| + | - Connect your RPC card by means of a USB-2-Serial converter | ||
| + | - Setup the ax0 kernel network device with kissattach. Edit /// | ||
| + | - Install xinetd | ||
| + | - Add the file below to a file in /// | ||
| + | - Use the DAPNET-Proxy to connect yourself with a DAPNET-Node | ||
| + | - Get your new transmitter registered into the DAPNET network (see above) | ||
| + | |||
| + | < | ||
| + | # description: | ||
| + | service rpc_db0sda | ||
| + | { | ||
| + | disable = no | ||
| + | type = UNLISTED | ||
| + | port = 19999 | ||
| + | id = funkruf | ||
| + | socket_type = stream | ||
| + | protocol = tcp | ||
| + | user = root | ||
| + | wait = no | ||
| + | server = / | ||
| + | server_args = -r -S -R -s db0sda-12 -r ax0 db0sda-7 | ||
| + | } | ||
| + | </ | ||
| + | In this example // | ||
| + | |||
| + | Further information on the [[dapnetproxy|DAPNET-Proxy]] is [[dapnetproxy|here]]. | ||
ax25.1515407097.txt.gz · Zuletzt geändert: 2018/01/08 10:24 von dh3wr