Benutzer-Werkzeuge

Webseiten-Werkzeuge


mmdvm

Dies ist eine alte Version des Dokuments!


MMDVM, MMDVM_HS_HAT, MMDVM_DUAL_HAT with Pi-Star (Pi*)

What do I need?

Hardware

  • MMDVM
  • MMDVM_HS_Hat
  • MMDVM_DUAL_HAT

with Firmware >= 1.4.1

Software

PiStar >= 3.4.16 or MMDVM-Host Version ???

Which Pagers can be used

Just these? Why list them again?

How to set up Pi* for PROCSAC (DAPNET) with MMDVM_HS_HAT or MMDVM_DUAL_HAT

Already have a working installation of Pi-Star (Pi*)?

Yes, I have already a running Pi-Star:

Update and Upgrade Pi*'s base system services and packages

  • Login to your Pi* Installation via SSH using Terminal,cmd-Promt or putty (Standard is „ssh pi-star@pi-star“ (you can miss the :22 at the end, because it is the standard port)
ssh pi-star@pi-star [Enter]

Now you will be asked for the Password - Standard-Password is „raspberry“ without „“ or take the password you have changed in Pi-Star Dashboard.

You will see the Welcome Message in ASCII-Signs

Now you have to Enter the following commands:

1. PI* uses a write protection so the command to unlock the filesystem for editing is:

rpi-rw [Enter]

2. Now get the latest Version of Pi* and all needed software components:

sudo pistar-update [Enter]

3. Upgrade the Pi* Installation to the next following Version:

sudo pistar-upgrade [Enter]

Repeat the last command (sudo pistar-upgrade) till you get a message „you have installed the latest Version of Pi* - No update needed“ or a similar message.

It is not possible to directly Upgrade to the newest Version! So you have to repeat the pistar-upgrade several times.

For example: You have installed Pi* Version 3.4.13 and want to get onto Version 3.4.16

You have to use the command „sudo pistar-upgrade“ 3 times to get from 3.4.13 to 3.4.14, than from 3.4.14 to 3.4.15 and 3rd time to get from 3.4.15 to 3.4.16.

The last output in terminal should be:

    You are already running the latest version…
    Sleeping a few seconds before making the disk Read-Only…
    Finished

Upgrade the firmware of your MMDVM-Hardware

for Upgrading MMDVM_HS_Hat board conected to GPIO you have to enter the command:

sudo pistar-mmdvmhshatflash hs_hat [Enter]

for upgrading the original MMDVM-HS_DUAL_HAT board (made by Andy, Florian (DF2ET) and DB9HAT) conected to GPIO you have to enter the command:

sudo pistar-mmdvmhshatflash hs_dual_hat

If you get a message that the flashing process was successfull, the hardest part is done. If not, repeat flashing or ask for help in the „MMDVM-BM“ or „DAPNET User“ Telegram-Messenger Groups.

Do a restart now with

sudo reboot now [Enter]

Configure Pi-Star and enable DAPNET

If not already done you should register on https://www.hampager.de and than Register a New Transmitter.

You will get a „DAPNET AuthKey“ by email if your ticket is arranged by a Team-Member.

Now it`s time to Login into the Pi*-Dashboard!

On a Windows, Mac, or Linux-based computer (not the hotspot itself) that has WiFi enabled, open a browser window and navigate to (trailing slash needed):

  Windows: http://pi-star/
  macOS, iOS, etc.: http://pi-star.local/
  On some mobile devices, the url won't work. In that case, try the Auto AP IP address: 192.168.50.1
  

Go to Admin Area and hit „Apply Changes“ somewhere, like if you would save any changes - even if you did not change anything. This will reload the page and force Pi* to reload store and reload the Configuration. During this process all missing or by update added sections will be loaded and shown correctly.

Now you should still see the Configuration view and in the „MMDVMHost Configuration“ section, switch on „PROCSAC“ and then click „apply changes“.

The Page will reload - now search for the „POCSAG Configuration“ section and fill out the needed values:

  • Node Callsign POCSAG – Enter the POCSAG node callsign.
  • Radio Frequency POCSAG – Enter the POCSAG radio frequency. Per Andy Taylor in the Pi-Star User Forum : „If we get good buy in from repeater keepers, we could have a really good paging network with great coverage, especially if we all use the same standard frequency.“ In Germany, where are already a lot of repeaters we use 439.987.500MHz, which will be the deafault entry in Pi*!
  • DAPNET AuthKey – Enter your authorization key for the Decentralized Amateur Paging Network. Which you got by Mail after you registered a New Transmitter as I told you on the Beginning of Configure Pi-Star and enable DAPNET

No Pi-Star installed yet:

Please google for a Pi-Star installation guide. A nice one is written by KE0FHS on https://www.toshen.com/ke0fhs/pi-star.htm or visit the main website of the PI-Star-Project under https://www.pistar.uk/

73, DO6DAD

mmdvm.1531401063.txt.gz · Zuletzt geändert: 2018/07/12 15:11 von dh3wr